Futaba T3PV Rattradio med R203GF S/T-FHSS

Lightweight
Easy-to-read screen
Super-fast response rate make a real difference on race day
FHSS, S-FHSS and T-FHSS protocols
R203GF is perfect match for brushless ESCs and digital servos.


T3PV Features:
◾System: FHSS, S-FHSS & T-FHSS 2.4GHZ (T-FHSS / Telemetry only available with the optional R304SB receiver)
◾3+1 Channels (the 4:th channel can only be used when 4WS mixing (crawlers) or Brake mixing and with a 4-channel receiver)
◾Channel 3 can be used on SW1 (two endpoints) or at DT3 where the D/R normally is at (stepped function)
◾10 Model Memory
◾4-Character Model Name
◾Sub-Trim (CH1-4)
◾Channel-4 Trim (only visible if 4WS or Brake Mixing is activated)
◾Steering Dual Rates (D/R)
◾Steering End Point Adjustement (EPA-CH1)
◾Throttle End Point Adjustement (EPA-CH2)
◾Channel-3 End Point Adjustement (EPA-CH3)
◾Channel-4 End Point Adjustement (EPA-CH4) - this is only displayed when 4WS or Brake Mixing is activated
◾4-Wheel-Steering / Brake Mixing (SMX) (booth mixers can't be used at the same time)
◾Sero Reverse (CH1-4)
◾Steering Exponential (EXP-CH1)
◾Throttle Exponential (EXP-CH2)
◾Throttle Fail-Safe (F/S)
◾ABS Brakes (3- cycle speeds available)
◾Model Data Copy
◾Auto Power-Off after 10 minutes

Low Battery Alarm:
◾4x AA alkaline batteries - set LBA @ 4.2V
◾5 cell (6V) NiMH - set LBA @ 5.0V
◾2S (6.6V) LiFe - set LBA @ 5.8V

Available T-FHSS Telemetry Functions when using the R304SB receiver (not included):
◾Receiver battery voltage (no sensor needed)
◾External voltage (if this sensor is used the receiver battery voltage is not visible on the TX LCD) - SBS-01V
◾No other telemetry sensors can be used

Suitable Receivers:
◾R203GF S-FHSS (included)
◾R304SB T-FHSS (optional) - Use only Futaba Digital & BLS servos

Optional TX Batteries:
◾4x AA alkaline batteries (battery holder included)
◾YT1800A (5 Cell NiMH)
◾HT5F1800B / FPEBA0142 (5 Cell NiMH)
◾FT2F1700B / FPEBA0140 (2S 6.6V LiFe)
◾FT2F2100B / FPEBA0135 (2S 6.6V LiFe)

T3PV-2.4G Transmitter:
◾FHSS/S-FHSS/T-FHSS* system
◾Wheel type
◾3+1 channels (the 4th channel is used for mixing functions only)
◾Transmitting frequency: 2.4GHz band
◾Power requirement: Size AA Dry cell battery x 4 (6V) (or 5-cell NiMH / 2-cell LiFe)
◾Current drain: 100mA or less
◾Transmission antenna: 1/2λ di-pole (Built-in)

Receiver R203GF (included):
◾3 channels
◾S-FHSS/FHSS auto detection system
◾Power requirement: 4.8V ~7.4V battery (Dry cell battery cannot be used)
◾Size: 39 x 26 x 10 mm (excluding a projection part)
◾Weight: 8 g